AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Sane linux network scanner1/2/2024 ![]() ![]() check_host: opening config file: /etc/hosts.equiv check_host: remote host doesn't have same addr as local check_host: local hostname(s) (from DNS): white check_host: remote host is not IN_LOOPBACK nor IN6_LOOPBACK check_host: access by remote host: 192.168.0.10 handle_connection: processing client connection run_standalone: waiting for control connection do_bindings: socket failed: Address family not supported by protocol do_bindings: to your /etc/services file (or equivalent). ![]() do_bindings: sane-port 6566/tcp saned # SANE network scanner daemon do_bindings: " sane-port " service unknown on your host you should add do_bindings: trying to get port for service "sane-port" (getaddrinfo) saned (AF-indep+IPv6) from sane-backends 1.0.22 starting up Thanks all in advance for your effort in helping me out,Ĭode: main: starting debug mode (level 5) Maybe someone could recommend me another forum or place to ask for help. I would also like to know where else should I look for a solution to this issue, already googled for hours and hours. I thought it could be a memory problem, since it does scan small areas, but it is not, in fact, the memory usage doesn't increase much during the scan, I even created a 128MB swap partition in my flash drive (was afraid of doing so, since it would wear it quickly, will probably remove now), but it didn't change anything, it still doesn't scan with more than 55% of the router's memory (16MB) free and more than 97% of the swap memory free. I would like to have the scanner function of my AiO printer working, at least to scan the full glass in low resolutions (<=150). I will get an Error during device I/O, even if I try to scan directly from scanimage. If i get a small area (around 1/4 of the full glass) it will scan at some times, if i increase the DPI, it won't scan. ![]() The problem is also related to DPIs, but I can't manage to get one full page with 75 DPI, which is the lowest possible. SANE + HPLIP 3.11.3a-1 + Tomato v ND USB Std + Hp Deskjet F380 (F300 series) only works with small scan areas. Jan 1 00:48:27 OpenWrt user.err syslog: io/hpmud/hpmud.c 341: device_cleanup: done closing device dd=1 Jan 1 00:48:27 OpenWrt user.err syslog: io/hpmud/hpmud.c 339: device_cleanup: close device dd=1. Jan 1 00:48:27 OpenWrt user.err syslog: io/hpmud/hpmud.c 327: device_cleanup: device uri=hp:/usb/Officejet_J5700_series?serial=CN82BCV1BC04T1 Jan 1 00:48:27 OpenWrt user.warn syslog: failed to open scan channel: scan/sane/hpaio.c 657 Jan 1 00:48:27 OpenWrt user.err syslog: io/hpmud/dot4.c 330: invalid DOT4InitReply: cmd=0, result=20, revision=1 Scanimage: open of device hpaio:/usb/Officejet_J5700_series?serial=CN82BCV1BC04T1 failed: Device 1 00:48:27 OpenWrt user.err syslog: io/hpmud/dot4.c 231: unable to read Dot4ReverseReply header: Resource temporarily unavailable bytesRead=0 Openwrt firmware: KAMIKAZE (bleeding edge, r19957)ĭevice `hpaio:/usb/Officejet_J5700_series?serial=CN82BCV1BC04T1' is a Hewlett-Packard Officejet_J5700_series scanimage -T ![]()
0 Comments
Read More
Leave a Reply. |